GIGAZoom Function for Instantaneous Full-Length Display of 1 GW of Data

1 Giga memory for full-length display and instantaneous zooming (to user-specified length)


 

Amount of time data can be recorded with 1 GW memory.

DualCapture: A Powerful Tool for Durability Test Data Analysis

During durability testing, it is necessary to monitor the long-term trends of your data as well as capture the high speed transients that might occur. This presents a challenge as trend data is usually recorded at a slower sampling speed that might miss the transient phenomena. To meet this challenge, the DL750 offers the DualCapture function.

DualCapture

Using DualCapture, you can now record your trend data with a slow sampling speed and still be able to capture the transient phenomena with a faster sampling speed.

 

The waveform shown above was captured at a sampling rate of 50 kS/s. The occurrence of noise can be confirmed in the graph, but the time resolution is too low to capture the waveform accurately.

With DualCapture, the user sets triggers for capturing sudden phenomena. Up to 100 phenomena can be collected in a memory length of 10 kW at a maximum sampling rate of 10 MS/s.

DL750 Module LineUp

• 701250 High-Speed 10 MS/s 12-Bit Isolation Module
  Broad bandwidth (3 MHz) and high accuracy (0.5%) inputs

• 701251 High-Speed 1 MS/s 16-Bit Isolation Module
  High resolution inputs combined with high-sensitivity (1 mV/div)

• 701255 High-Speed 10 MS/s 12-Bit Non-Isolation Module
  Non-isolated model with the same performance as the model 701250

• 701260 High-Voltage 100 kS/s 16-Bit Isolation Module (with RMS)
  850 V (DC+ACpeak) direct input, RMS mode support
  Accuracy of 0.25%

• 701261/701262 Universal Module (2CH)
  Multiple inputs of general-use voltage and temperature module, two isolated inputs (Voltage: 5mV/div-20V/div, 100kS/s, 16bit; Temperature: TC- K, E, J, T, L, U, N, R, S, B, W, Iron-Doped, Gold/Chromel, 500S/s), two types of modules: with or without AAF (Anti-Aliasing Filter)

• 701265 Temperature/High-Precision Voltage Module
  100 Hz frequency range, high-accuracy (0.08%) voltage measurements, and ultra high-sensitivity range value (100 µV/div)

• 701270 Strain Modules NDIS-type
  Wide ranges of bridge voltage (2 V, 5 V, & 10 V)
  Accuracy of 0.5%
   
• 701271 Strain Modules DSUB-type
  Wide ranges of bridge voltage (2 V, 5 V, & 10 V)
  Accuracy of 0.5%

• 701275 Acceleration/Voltage Module (2 CH)
  Inputs for both acceleration and voltage, built-in AAF (anti-aliasing filter), supports built-in amp type acceleration sensors (4 mA/22 V), isolated input.

• 701280 Frequency Module (2 CH)
  High speed (40 µs, 25 kHz) update rates, 0.01 Hz-200 kHz frequency range, 9 measurement modes, built-in real-time digital filters, deceleration/stop prediction, offset observation function, isolated input, multiple input types (direct input from electromagnetic pickups, 300 Vrms AC power supply input, contact input, chatter elimination function)

Firmware Upgrade (Ver 3.01 or later)

More Advanced, More Convenient

• Numerical Monitor Function
  The waveform numeric level (instantaneous value) updates approximately every second even when starting, stopping, or performing long-term observation of a waveform. Useful for confirming the waveform input condition, or temperature/DC waveform levels. Confirm the levels of up to 16 channels simply by pressing the ESC key.
• Supports 100 kW-FFT
  Increased from 10 kW to 100 kW, 10 kW (8 ch), 100 kW/50 kW (2 ch)
• Improved Statistical Functions
  Supports history statistics. Increased number of cycle statistics items (from 24,000 to 48,000).
• Knocking Filter Function (DSP Channel Function)
  Offers dedicated menus for extracting the knocking portion of the waveform from the rest of the engine cylinder pressure waveform. HPF, BPF, and differential filters available. Includes functions for eliminating noise when the bulb opens/closes and for triggering on filtered waveforms. Max 6 channels and OR trigger are available.